Braeburn 5200 Bedienungsanleitung PDF herunterladen

MODEL

5200

USER MANUAL

READ ALL INSTRUCTIONS BEFORE PROCEEDING

CONTENTS

WARNING!

Important Safety Information

SPECIFICATIONS

INSTALLATION

2.1

Replacing Existing Thermostat

Always turn off power to the air conditioning or heating system prior to removing

existing thermostat.

Remove the cover of your old thermostat and locate the wire terminals. Do not remove

wires from terminals yet.

Using small pieces of masking tape, label wires prior to removal from terminals. Use

the chart below to determine the new terminal designations for your new thermostat.

Premier Series

Universal 7 Day or 5-2

Day Programmable

2 Heat/2 Cool Heat Pump

Digital Thermostat

Old Terminal from New Terminal for

Existing Thermostat New Thermostat Terminal Description

R, V-VR or VR-R R 24 Volt AC

Y, Y1 or M Y1 Stage 1 Cooling or Heating

Y2 Y2 Stage 2 Cooling

W1, W2 or W-U W2 Stage 2 Heating

E E Emergency Heating

G or F G Fan Control

O or R O Reversing Valve (Cooling)

B B Reversing Valve (Heating)

L or X L System Status LED

C, X or B C 24 Volt AC, Transformer Common

Compatible with low voltage multi-stage heat

pump systems with up to two stages of heating

and two stages of cooling. Not for use on

single-stage heating or cooling systems.

• Always turn off power to the air conditioning or heating system prior to installing, removing,

cleaning or servicing thermostat.

• Read this manual thoroughly prior to installing, programming or operating this thermostat.

• This thermostat is designed for use with a 24 Volt AC low voltage multi-stage heat pump system.

• Do not use this thermostat on systems with voltages higher than 30 Volts AC.

• This thermostat requires 24 Volt AC Power for normal operation and control of the heating or

cooling system.

• The thermostat also requires two (2) properly installed "AA" alkaline batteries to retain clock

settings in the event of loss of AC Power due to power outage or rolling blackouts.

• Wiring must conform to all building codes and ordinances as required by local and national code

authorities having jurisdiction.

• Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system

control board to test the thermostat installation. This could damage the thermostat and void

the warranty.

• Do not select COOL mode of operation if the outside temperature is below 50˚ F (10˚ C). This

could possibly damage the controlled cooling system and may cause personal injury.

• This thermostat should only be used as described in this manual. Any other use is not

recommended and will void the warranty.

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

3 amp maximum load (all terminals)

• Control Range: 45˚ - 90˚ F (7˚ - 32˚ C)

• Accuracy: +/- 1˚ F (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• DC Back-Up Power: 3.0 Volt DC (2 AA Alkaline batteries included)

• Compatibility: Multi-stage heat pump systems with up to two stages

of heating and two stages of cooling

• Terminations: R, Y1, Y2, W1, W2, E, G, O, B, L, C

SPECIFICATIONS

INSTALLATION

TESTING YOUR NEW THERMOSTAT

PROGRAMMING USER SETTINGS

ADDITIONAL OPERATION FEATURES

TROUBLESHOOTING

WIRING DIAGRAM

1 2 3 4 5 6 7 8 9

Inhaltsverzeichnis

Seite 1 - USER MANUAL

Seite 2 - NEW THERMOSTAT

2 3INSTALLATION22.1Replacing Existing Thermostat cont.4. After labeling and removing all wires from terminals, unscrew the existing thermostat sub-

Seite 3

454.2Setting Current Time of Day and Day of WeekNOTE: It is important for you to set the current time of day (note AM/PM indicator in display), and

Seite 4 - USER SETTINGS

6 7Weekday Weekend4.4Setting Your Energy Saving Programs–Tips Before Starting• It is important for you to set the current time of day (note the

Seite 5 - IMPORTANT NOTE!

84.4Setting Your Energy Saving Programs cont.Entering Your Program1. Place the system switch in the HEAT mode of operation. 2. Press the PROG button

Seite 6 - OPERATION FEATURES

10 115.1Review Set Temperature5.2Temporary Program OverrideThe Model 5200 is equipped with an auxiliary heat option switch which is set at installatio

Seite 7 - TROUBLESHOOTING

12 13NOTE: The installer can reset the thermostat and bypass the compressor protection features by pressing the RESET button. This will erase all ent

Seite 8

1415TROUBLESHOOTING6cont.SYMPTOM POTENTIAL SOLUTIONVerify your program setpoint time entries. The heating and cooling programs utilize the same setpoi

Seite 9 - Store this

The Keypad is locked. Press both the or key together at the same time for one second to unlock (see section 5.5).16TROUBLESHOOTING6cont.SYMPTO

Weitere Dokumente für Thermostate Braeburn 5200

Um das Dokument anzuzeigen Braeburn 5200 Spezifikationen

Braeburn 5200 Spezifikationen (11 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Braeburn 5200 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Thermostate Braeburn 5200 herunter. Braeburn 5200 User manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Thermostate Braeburn 5200

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate Braeburn 5200