Braeburn 6100 Spezifikationen PDF herunterladen (Seite 13)

13 Installer Guide

16 AC Power Interrupt Warning [note 6]–Whenenabled,thethermostatwilldisplayanoutagewarning

 whenACpowertothethermostatislost.

17 Short Cycle Protection–Selectsthenumberofminutesthecoolingcompressorwillbelockedoutafter

 turningoff.Thisshortcycleprotectionisalsoactiveintheheatmodeifaheatpumpsystemwasselectedin

 Option6.

18 Residual Cooling Fan Delay–Selectsadelayforthesystemfanafterthecoolingcompressorhasturned

 off.Thisdelaywillhelpremovetheremainingcoolairoutoftheductworkprovidingadditionalefciency.

19 Circulating Fan Lock–Whenenabled,theonlyuserfanoptionsavailableareONandCIRC(Circulation).

 TheAUTOoptionisnotavailablewiththisoptionenabled.

20 Adaptive Recovery Mode (early recovery) [note 7]–EnablesordisablestheARM

(adaptiverecovery

 mode)feature.DuringARM,roomtemperatureisrecoveredbyturningontheheatingorcoolingbeforethe

 endofthesetbackperiod.Thesetpointtemperatureischangedtothatoftheupcomingprogramtemperature.

21 Indoor Remote Sensor Control [note 8]–IfaBraeburn

indoorremotesensorisconnectedduring

 installation,thethermostatwillautomaticallydetectthesensor.Whenanindoorsensorisdetected,youmay

 selectbetweenthermostatonly(ISENS),remotesensoronly(ESENS)orcombiningthethermostatandthe

 remotesensor(ASENS).NOTE: This option does not apply to a Braeburn outdoor sensor. When an outdoor

sensor is connected the thermostat automatically recognizes it and no further conﬁguration is necessary.

22 Lockout Security Level–Selectsthelevelofkeypadlockoutwhenthethermostatislocked.Level2locks

theentirethermostat(includingthefrontresetbutton).Level1lockseverythingexcepttheSpeedBar

 allowingforupanddowntemperatureadjustment.NOTE: The lock code is set in the User Settings mode

(see User Manual).

23 Humidiﬁcation Mode (6400 only)–Selectsbetweendisablinghumidication(OFF),dependantcontrol

 (DEP)orindependentcontrol(IND).TheDEPsettingcontrolshumidicationonlyduringacallforheating.

 TheINDsettingallowshumidicationoutputintheheatmode,butdoesnotrequireacallforheating.

NOTE: It is recommended that the IND setting only be used with systems designed for low air temperature

humidiﬁcation such as steam humidiﬁcation. Always ensure the heat exchanger or other system parts are

not exposed to excess water from condensation or other sources. When there is any doubt, use the OFF or

DEP setting.

24 Auto Humidity Set Point Limit (6400 only) [notes 9, 11]–Selectbetweenturningtheautomatichumidity

 setpointlimittoauto(AUTO)ormanual(MAN).WhenAUTOisselected,humiditycontrolisprovidedauto-

 maticallybasedontheoutdoortemperature.SelectingMANallowsyoutomanuallycontrolthelevel

 ofhumidity.

25 Dehumidiﬁcation (6400 only)–Selectbetweenenabling(ON)anddisabling(OFF)dehumidicationcontrol

 (Dterminal).Forusewithadehumidier.

26 Auto Changeover Dead Band [note 10]–Whenautochangeovermodeisenabledinoption5and

 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingwhentheroomtemperature

 meetsthenormalcriteriaforeitheraheatingorcoolingcall.Thereisaforcedseparation(deadband)

 betweentheheatingandcoolingsetpointssothatthesystemsdonotworkagainsteachother.This

 optionselectstheamountofthisdeadbandindegreeswiththedefaultbeing3°F.

27 Compressor Balance Point [notes 4, 11]–Locksouttheuseofthecompressorheatstagewhenthe

 outsideairtemperatureislessthantheselectedsettingof15°Fto50°F(-9°Cto10°C)

28 Auxiliary Heat Balance Point [notes 4, 11]–Locksouttheuseoftheauxiliaryheatstagewhenthe

 outsideairtemperatureexceedstheselectedsettingof70°Fto40°F(21°Cto4°C).NOTE: This balance

point overrides the fossil fuel compressor lockout in option 14. If this option is set to gas and the outdoor

temperature is over the auxiliary balance point, the compressor will remain on during a call for auxiliary heat.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18

Kommentare zu diesen Handbüchern

Keine Kommentare

Braeburn 6100 Spezifikationen Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate Braeburn 6100