Braeburn 1200NC Betriebsanweisung PDF herunterladen

This thermostat requires 24 Volt AC Power or two (2) properly installed

“AA” Alkaline batteries for proper operation. When connecting 24 Volt

AC Power the batteries may be installed as a backup.

For use only as described in this manual. Any other use

will void warranty.

1000NC

Single Stage Heat / Cool

Conventional and Heat Pump

Speciﬁcations

About Your Thermostat

Installation

System Testing

Setting User Options

Operating Your Thermostat

Additional Operation Features

Thermostat Maintenance

Warning

Turn off power to the heating or cooling

equipment before installation.

Attention

For installation by experienced service

technicians only.

Follow applicable codes.

1200NC

Up to 2 Heat / 1 Cool

Conventional and Heat Pump

Read all instructions before proceeding.

This thermostat is compatible with:

  • Singlestageheat/coolconventionalandheatpumpsystems

  • Conventionalsystemsupto2heat/1cool(1200NConly)

  • Singlecompressorheatpumpsystemswithanauxiliaryheatstage(1200NConly)

  • 250–750millivoltheatonlysystems

Electrical and control speciﬁcations:

 •ElectricalRating:24VoltAC

  •1ampmaximumloadperterminal

  •ACPower:18–30VoltsAC

  •DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  •ControlRange:45°–90°F(7°–32°C)

  •TemperatureAccuracy:+/-1°F(+/-.5°C)

Terminations

  •1000NC–Rc,Rh,O,B,Y,W,G,C

  •1200NC–R,O,B,Y1,E/W1,G,W2,C

Speciﬁcations

1000NCW-100-12

Non-Programmable

Thermostats

Model number is located on back of thermostat

Detailed

User Guide

1 2 3 4 5 6 ... 10 11

Inhaltsverzeichnis

Seite 1 - User Guide

This thermostat requires 24 Volt AC Power or two (2) properly installed “AA” Alkaline batteries for proper operation. When connecting 24 Volt AC Power

Seite 2 - Installation

1.Openthebatterydoorlocatedonthe bottomofthethermostat.2.Removeoldbatteriesandreplace withnewbatteries.3.Makesuretocorrec

Seite 3 - Provide Power

Seite 4 - Typical Wiring Conﬁgurations

15 Setting User Options 6 Operating Your Thermostat7 Additional Operation Features8 Thermostat MaintenanceFor installation by experienced service tec

Seite 5 - (Continued)

2Install your new Braeburn thermostat in 5 basic steps:1 InstalltheSub-Base2 ProvidePower3 ConnectYourWires4 SetInstallerSwitches5 Attach

Seite 6 - installer switches

3Terminal Function Description Rc*   Input 24VoltACCoolingTransformer       (DualTransformerSystemsOnly) Rh*   Input Po

Seite 7 - Setting User Options

4NOTES - Conventional Systems[1]Ifbatteriesareinstalledthe24VoltACcommonconnectionisoptional[2]Removefactoryinstalledjumperfordualt

Seite 8 - Operating Your Thermostat

Factory Setting Switch Default Options Comments5Heat Pump Systems (cont.)NOTES - Heat Pump Systems[1]Ifbatteriesareinstalledthe24Vol

Seite 9 - Thermostat Maintenance

64System TestingWarningRead Before Testing• Donotshort(orjumper)acrossterminalsonthegasvalveoratthe heatingorcoolingsystemcontrol

Seite 10 - Limited Warranty

7 User Factory Setting No. Options Default Options Comments  1 1ststage0.5 0.5, 1.0 Selecta1ststagetemperature   differ

Seite 11

8Detailed Explanation of User Options: Temperature Differential(User Option 1 and 2)Thedifferentialsettingisthetemperaturecontrolrangethatyou